Top 10 typical forklift crashes ， forklift procedure must take notice of these issues ！.

Do not underestimate the forklift at work. If the procedure is bad, there will certainly be significant crashes in minutes, and there are numerous mishaps entailing forklifts.

Situation 1: The forklift cargo blocked the driver's sight, and the person in front can not be located, resulting in a rolling mishap.
Case 2: In order to maintain the balance of the forklift when raising hefty goods, the staff members used their body weight as the counterweight, which virtually created casualties.
Case 3: The width of the forklift cargo exceeds the allowed width of the route and hangs on the roadside shelf, which practically triggers an crash.
Instance 4: Forklift is speeding up and surrender throughout a turn.
Case 5: The forklift chauffeur did not notice the pedestrian, and the pedestrian did not discover the forklift.
Instance 6: The forklift raises the workers illegally, the forklift driver does not put on the safety belt, the forklift lifter falls and the driver is squashed when the forklift rolls over.
Instance 7: The forklift vehicle driver did not put on a safety belt and fell from the vehicle when it rolled over and was crushed.
Forklift procedure should take notice of these issues ：.

Start.
1. Before beginning, observe the environments, and after confirming that there are no obstacles that hinder the safety and security of driving, honk the horn first and afterwards start.
2. For lorries with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale need to be secure prior to starting.
3. When the forklift begins with a lots, the chauffeur should first verify that the load is steady and dependable.
4. The beginning should be slow-moving and constant.

Driving.
1. When driving, the height in between the bottom end of the fork and the ground need to be kept at 300mm-400mm, and the pole must be slanted in reverse. .
2. Do not raise the fork too high when driving. When getting in and leaving the work website or while driving, take care that there will certainly be no obstacles overhead. When the load is traveling, the fork has to not be elevated expensive, which will affect the security of the forklift. .
3. After discharging, the fork needs to be reduced to the normal driving placement before driving. .
4. When turning, if there are pedestrians or automobiles nearby, the driving signal needs to be issued initially. High-speed doglegs are forbidden. High-speed sharp turns will certainly cause the automobile to shed lateral stability and topple. .
5. When the forklift is downhill, it is strictly prohibited to turn off the flame and slide, and it is restricted to brake all of a sudden while driving with tons unless there are special situations.
6. When the forklift is running, it has to follow the web traffic rules in the manufacturing facility and should maintain a particular safety range from the lorry in front. .
7. When the forklift is running, the load has to be in the most affordable setting that does not prevent the driving, and the gantry should be appropriately tilted back. The lots will not be raised except when piling or loading. .
8. The height of the load should not block the chauffeur's view. In unique circumstances, when the product influences the forward vision, drive at a low speed when reversing.
9. It is prohibited to activate the ramp, nor to drive across the ramp. .
10. The risk-free driving speed of the forklift in the factory location is 5 km/h, and it must drive safely at a reduced speed when going into the production workshop area. .
11. When the forklift is raised, raised or driven, it is prohibited for personnel to stand on the fork to hold things and play a stabilizing role. .
12. If problems are located, they will certainly be fixed and reported in a prompt manner, and they will certainly never ever operate with diseases or conceal them.

filling and dumping.
1. When fork-loading things, the range between both forks must be adjusted as required to make the tons of the two forks well balanced and not skewed, and one side of the thing must be against the shelf. .
2. It is prohibited to work with a solitary fork or use a fork top or draw. In special conditions, security warning signs must be established to remind bordering pedestrians. .
3. In the process of loading and dumping products, the forklift has to be braked with the brake. .
4. The rate of the car should be sluggish and steady. Beware not to roll the wheels on the dunnage, so as not to stretch the rolled items and injure people. .
5. When making use of a fork to fork the goods, the fork ought to be as deep as Electric Forklift Truck for Warehouse feasible under the load, and it must be kept in mind that the fork suggestion need to not touch other products or things. The load must be stabilized with very little back tilt of the gantry to make sure that the load does not move in reverse. The mast can be tilted onward slightly when the tons is Stand-on Electric Pallet Stacker decreased to allow for easy positioning of the lots and extraction of the forks. .
6. It is forbidden to fork products at broadband and collide with hard items with the fork head. .
7. When the forklift is working, it is restricted for individuals to stand around the fork, so as to prevent the collapse of the goods and hurt individuals. .
8. Overloading is forbidden, and it is banned to use forks to lift workers to participate in high-altitude procedures to stay clear of high-altitude dropping accidents. .
9. It is not allowed to use the brake inertia to slip, put, round or roll items. .
10. It is not enabled to make use of forks to select, transform pallet dump.

Leaving .
1. It is forbidden to leave the forklift when the items on the fork are in the air. Before leaving the forklift, you should discharge the goods or lower the fork framework.
2. Pull the emergency brake manage to dead or depress the emergency brake switch.
3. The engine is shut off and the power is cut off. (Except for special situations, such as the motorist does not leave the automobile's line of vision and does not surpass 1 minute).
4. Remove the key. .

Forklift Operation Precautions.
1. Before and after the forklift procedure, the look must be inspected, and fuel, lubricating oil and cooling water should be included.
2. Examine the safety and security performance of starting, running and braking.
3. Examine whether the lights and horn signals are full and efficient.
4. During the operation of the forklift, examine whether the stress and temperature are normal.
5. After the forklift is running, the external leak must likewise be checked and the seals should be replaced in time.

Forklift Safety Operation Specifications.
1. You should check prior to leaving the auto;.
2. When you come across somebody in front of you throughout driving, you ought to send a signal at a distance of 5 m;.
3. The driving rate in the factory does not exceed 5 km/h;.
4. When driving, the nadir of the cargo need to be 0.3 m ~ 0.4 m in the air;.
5. The turning need to not be as well sharp to prevent the propensity of " totally free switching";.
6. Running up and down the slope must be slow and consistent, and no switching on the incline is enabled.
7. Do not drive throughout the gradient. When the slope is higher than 10%, the vehicle must be driven backwards when declining;.
8. When the forklift personnel lug the goods and move forward, if they come across large or hefty goods and go to the vehicle driver's line of vision, they need to take the reversing workout
.
The "Eight Prohibitions" should be complied with in the operation.
1. Single fork procedure is not allowed.
2. It is not enabled to raise the goods for long distance driving.
3. It is not enabled to grab the goods by turning over the pallet with the fork.
4. It is not permitted to straight shovel chemicals, flammables and other harmful chemicals with forks.
5. It is not permitted to use inertia pressure to grab the goods.
6. It is not allowed to utilize stopping pressure to expatriation round or easy-to-roll objects.
7. It is not enabled to bring individuals to work with the pallet or fork, and it is strictly forbidden to stand under the fork after the fork is increased.
8. Do not drive side to side on inclines
.
Vehicle parking is not allowed under the list below conditions.
1. Curves, narrow roads, train crossings;.
2. Areas with a longitudinal incline greater than 5%.
3. When there is an obstacle on one side of the road, the opposite side of the area with the exact same size as the barrier should be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844